Tektronix(泰克)DPO4034 混合信号示波器

Characteristic	DPO4034	DPO4054	DPO4104
Input Channels	4	4	4
Analog Bandwidth (-3 dB) 5 mV/div - 1 V/div	350 MHz	500 MHz	1 GHz
Calculated Rise Time 5 mV/div (typical)	1 ns	700 ps	350 ps
Hardware Bandwidth Limits	20 MHz or 250 MHz
Input Coupling	AC, DC, GND
Input Impedance	1 MΩ ±1%, 50 Ω ±1%
Input Sensitivity, 1 MΩ	1 mV/div to 10 V/div
Input Sensitivity, 50 Ω	1 mV/div to 1 V/div
Vertical Resolution	8 bits (11 bits with Hi Res)
Max Input Voltage, 1 MΩ	250 V_RMS with peaks ≤ ±400 V
Max Input Voltage, 50 Ω	5 V_RMS with peaks ≤ ±20 V
DC Gain Accuracy	±1.5% with offset set to 0 V
Offset Range	1 MΩ	50 Ω
1 mV/div to 50 mV/div	±1 V	±1 V
50.5 mV/div to 99.5 mV/div	±0.5 V	±0.5 V
100 mV/div to 500 mV/div	±10 V	±10 V
505 mV/div to 995 mV/div	±5 V	±5 V
1 V/div to 5 V/div	±100 V	±5 V
5.05 V/div to 10 V/div	±50 V	NA
Channel-to-Channel Isolation	≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth for any two channels having equal volts/div settings

Characteristic	DPO4034	DPO4054	DPO4104
Maximum Sample Rate (all channels)	2.5 GS/s	2.5 GS/s	5 GS/s
Maximum Record Length (all channels)	10 M points
Maximum Duration at Highest Sample Rate (all channels)	4 ms	4 ms	2 ms
Time Base Range (s/div)	1 ns to 400 s		400 ps to 400 s
Time Base Delay Time Range	-10 divisions to 50 s
Channel-to-Channel Deskew Range	±100 ns
Time Base Accuracy	±5 ppm over any ≥1 ms interval

Characteristic	Description
Main Trigger Modes	Auto, Normal, and Single
Trigger Coupling	DC, HF reject (attenuates >50 kHz), LF reject (attenuates
Trigger Holdoff Range	20 ns to 8 s
Sensitivity
Internal DC Coupled	0.4 div DC to 50 MHz increasing to 1 div at rated bandwidth
External (auxiliary input)	200 mV from DC to 50 MHz increasing to 500 mV at 250 MHz
Trigger Level Range
Any Channel	±8 divisions from center of screen
External (auxiliary input)	±8 V

Mode	Description
Sample	Acquire sampled values
Peak Detect	Captures glitches as narrow as 200 ps at all sweep speeds
Averaging	From 2 to 512 waveforms included in average
Envelope	Min-max envelope reflecting Peak Detect data over multiple acquisitions
Hi Res	Real-time boxcar averaging reduces random noise and increases resolution
Roll	Scrolls waveforms right to left across screen at sweep speeds slower than or equal to 40 ms/div

Mode	Description
Edge	Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, HF reject, LF reject, and noise reject
Pulse Width	Trigger on width of positive or negative pulse that are >,
Runt	Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again
Logic	Trigger when any logical pattern of channels goes false or stays true for specified period of time. Any input can be used as a clock to look for the pattern on a clock edge. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as High, Low, or Don't Care
Setup and Hold	Trigger on violations of both setup time and hold time between clock and data present on any two input channels
Rise/Fall Time	Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either
Video	Trigger on all lines, odd, even, or all fields on NTSC, PAL, and SECAM video signals
Extended Video (optional)	Trigger on 480p/60, 576p/50, 720p/30, 720p/50, 720p/60, 875i/60, 1080i/50, 1080i/60, 1080p/24, 1080p/24sF, 1080p/25, 1080p/30, 1080p/50, 1080p/60, and custom bi-level and tri-level sync video standards
I²C (optional)	Trigger on Start, Repeated Start, Stop, Missing ACK, Address (7 or 10 bit), Data, or Address and Data on I²C buses up to 3.4 Mb/s
SPI (optional)	Trigger on SS, Idle Time, MOSI, MISO, or MOSI and MISO on SPI buses up to 10.0 Mb/s
CAN (optional)	Trigger on Start of Frame, Frame Type (data, remote, error, overload), Identifier (standard or extended), Data, Identifier and Data, End of Frame, or Missing ACK, or Bit Stuffing Errors on CAN signals up to 1 Mb/s. Data can be further specified to trigger on ≤, , ≥, or ≠ a specific data value. User-adjustable sample point is set to 50% by default
RS-232/422/485/UART (optional)	Trigger on Tx Start Bit, Rx Start Bit, Tx End of Packet, Rx End of Packet, Tx Data, and Rx Data
LIN (optional)	Trigger on Sync, Identifier, Data, Identifier and Data, Wakeup Frame, Sleep Frame, or Errors such as Sync, Parity, or Checksum Errors
FlexRay (optional)	Trigger on Start of Frame, Type of Frame (Normal, Payload, Null, Sync, Startup), Identifier, Cycle Count, Complete Header Field, Data, Identifier and Data, End of Frame or Errors such as Header CRC, Trailer CRC, Null Frame, Sync Frame, or Startup Frame Errors.
Trigger Delay by Time	4 ns to 8 s
Trigger Delay by Events	1 to 9,999,999 events

Characteristic	Description
Cursors	Waveform and Screen
Automatic Measurements	29, of which up to eight can be displayed on screen at any one time. Measurements include Period, Frequency, Delay, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area, and Cycle Area
Measurement Statistics	Mean, Min, Max, Standard Deviation
Reference Levels	User-definable reference levels for automatic measurements can be specified in either percent or units
Gating	Isolate the specific occurrence within an acquisition to take measurements, on using either the screen or waveform cursors

Option	Description
Arithmetic	Add, subtract, multiply, and divide waveforms
Math Functions	Integrate, Differentiate, FFT
FFT	Spectral magnitude. Set FFT Vertical Scale to Linear RMS or dBV RMS, and FFT Window to Rectangular, Hamming, Hanning, or Blackman-Harris
Advanced Math	Define extensive algebraic expressions including waveforms, math functions, scalars, up to two user-adjustable variables, and results of parametric measurements e.g. (Intg(Ch1-Mean(Ch1)) × 1.414 × VAR1)

Application	Description
NI LabVIEW SignalExpress™ Tektronix Edition LE	A fully interactive measurement software environment optimized for the DPO4000 Series, enables you to instantly acquire, generate, analyze, compare, import, and save measurement data and signals using an intuitive drag-and-drop user interface that does not require any programming. Standard DPO4000 Series support for acquiring, controlling, viewing, and exporting your live signal. The full version (SIGEXPTE) adds additional signal processing, advanced analysis, mixed signal, sweeping, limit testing, and user-defined step capabilities and is available for a 30-day trial period standard with each instrument
OpenChoice^® Desktop	Enables fast and easy communication between a Windows PC and the DPO4000 Series, through USB or LAN. Transfer and save settings, waveforms, measurements, and screen images.
IVI Driver	Provides a standard instrument programming interface for common applications such as LabVIEW, LabWindows/CVI, Microsoft .NET, and MATLAB

Characteristic	Description
Display Type	10.4 in. (264 mm) liquid-crystal TFT color display
Display Resolution	1,024 (H) × 768 (V) pixels (XGA)
Waveform Styles	Vectors, Dots, Variable Persistence, Infinite Persistence
Graticules	Full, Grid, Cross Hair, Frame, IRE, and mV
Format	YT and simultaneous XY/YT
Waveform Capture Rate	Up to 50,000 wfms/s

Port	Description
CompactFlash Drive	Front-panel access (Type 1)
USB 2.0 Full-speed Host Port	Supports USB mass storage devices and printers. Two ports available on rear panel and one on front panel
USB 2.0 High-speed Device Port	Rear-panel connector allows for control of oscilloscope through USBTMC or GPIB with a TEK-USB-488
LAN Port	RJ-45 connector, supports 10/100Base-T
XGA Video Port	DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector
Auxiliary Input	Front-panel BNC connector. Input Impedance 1 MΩ. Max input 250 V_RMS with peaks ≤ ±400 V
Probe Compensator Output	Front-panel pins. Amplitude 2.5 V. Frequency 1 kHz
Trigger Out	Rear-panel BNC connector, provides a positive polarity pulse when the oscilloscope triggers
Kensington Lock	Rear-panel security slot connects to standard Kensington lock

Characteristic	Description
Power Source Voltage	100 to 240 V ±10%
Power Source Frequency	47 – 66 Hz (90 to 264 V) 360 – 440 Hz (100 to 132 V)
Power Consumption	250 W maximum

Characteristic

Description

Power Source Voltage

100 to 240 V ±10%

Power Source Frequency

47 – 66 Hz (90 to 264 V)

360 – 440 Hz (100 to 132 V)

Power Consumption

250 W maximum

Dimensions	mm	in.
Height	229	9.0
Width	439	17.3
Depth	137	5.4
Weight	kg	lb.
Net	5	11
Shipping	10	22
Rackmount Configuration	5U
Cooling Clearance	2 in. (51 mm) required on left side and rear of instrument

Characteristic	Description
Temperature
Operating	0 °C to +50 °C
Nonoperating	-20 °C to +60 °C
Humidity
Operating	High: 40 °C to 50 °C, 10% to 60% Relative Humidity Low: 0 °C to 40 °C, 10% to 90% Relative Humidity
Nonoperating	High: 40 °C to 60 °C, 5% to 60% Relative Humidity Low: 0 °C to 40 °C, 5% to 90% Relative Humidity
Altitude
Operating	3,000 meters (9,843 feet)
Nonoperating	12,000 meters (39,370 feet)
Random Vibration
Operating	0.31 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total
Nonoperating	2.46 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total
Regulatory
Electromagnetic Compatibility	89/336/EEC
Safety	UL61010-1, Second Edition; CSA61010-1 Second Edition, EN61010-1: 2001; IEC 61010-1: 2001

DPO4034

此产品已经停止销售，请与我们联系获得更多帮助。

Characteristics

General Characteristics