TDS5104B

概述

技术指标

此产品已经停止销售，请与我们联系获得更多帮助。

Characteristics

Vertical System

Characteristic	TDS5034B	TDS5054B	TDS5104B
Input Channels	4
Analog Bandwidth (–3 dB) 5 mV/div - 1 V/div	350 MHz	500 MHz	1 GHz
Calculated Rise Time 5 mV/div (Typical)	1.15 ns	800 ps	300 ps
Hardware Bandwidth Limits	150 MHz or 20 MHz
Input Coupling	AC, DC, GND
Input Impedance, 1 MΩ	±1%
Input Impedance, 50 Ω	±1%		±2.5%
Input Sensitivity, 1 MΩ	1 mV/div to 10 V/div
Input Sensitivity, 50 Ω	1 mV/div to 1 V/div
Vertical Resolution	8 bits (>11 bits w/ averaging)
Max Input Voltage, 1 MΩ	150 V CAT I, ≤400 V peak. Derate at 20 dB/decade to 9 V_RMS above 200 kHz
Max Input Voltage, 50 Ω	5 V _RMS with peaks < ±30 V		<100 mV/div <1 V_RMS ≥100 mV/div <5 V_RMS
DC Gain Accuracy	1.5% with offset set to 0 V
Offset Range, 1 MΩ	1 mV/div - 99.5 mV/div ±1 V 100 mV/div - 1 V/div ±10 V 1.01 V/div - 10 V/div ±100 V
Offset Range, 50 Ω	1 mV/div - 99.5 mV/div ±1 V 100 mV/div - 1 V/div ±10 V		1 mV/div - 50 mV/div ±0.5 V 50.5 mV/div - 99.5 mV/div ±0.25 V 100 mV/div - 500 mV/div ±5 V 505 mV/div - 1 V/div ±2.5 V
Channel-to-Channel Isolation for Any Two Channels at Equal Vertical Scale	≥100:1 at ≤100 MHz and ≥30:1 at >100 MHz up to the rated bandwidth

Time-base System

Characteristic	Description
Time-base Range	200 ps/div to 1000 s/div
Time-base Delay Time Range	(s/div × 10) to 1000 s
Channel-to-Channel Deskew Range	±75 ns
Time-base Accuracy	15 ppm
Delta Time Measurement Accuracy	(0.06/sample rate + 15 ppm × \|Reading\|) RMS
Trigger Jitter (RMS)	8 ps_RMS (typical)
Long-term Sample Rate and Delay Time Accuracy	±15 ppm over any ≥1 ms interval

Acquisition System

Characteristic	TDS5034B	TDS5054B / TDS5104B
Real-time Sample Rates
1 Channel (Max)	5 GS/s
2 Channels (Max)	2.5 GS/s
3-4 Channels (Max)	1.25 GS/s
Equivalent Time Sample Rate (Max)	250 GS/s
Maximum Record Length per Channel with Standard Memory	8M/4M/2M	16M/8M/4M
With Opt. 3M	16M/8M/4M	NA

Maximum Duration at Highest Real-time Resolution (1 ch)

Characteristic	TDS5034B	TDS5054B / TDS5104B
Time Resolution (Single shot)	200 ps (5 GS/s)
Max Duration with Standard Memory	1.6 ms	3.2 ms
Max Duration with Opt. 3M	3.2 ms	NA

Characteristic

TDS5034B

TDS5054B / TDS5104B

Time Resolution

(Single shot)

200 ps (5 GS/s)

Max Duration with Standard Memory

1.6 ms

3.2 ms

Max Duration with Opt. 3M

3.2 ms

Acquisition Modes

Characteristic	Description
FastAcq Acquisition	FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events. Maximum FastAcq waveform capture rate is 100,000 wfms/s
Sample	Acquire sampled values
Peak Detect	Captures narrow glitches (<1 ns) at all real-time sampling rates
Averaging	From 2 to 10,000 waveforms included in average
Envelope	From 2 to 20,000,000 waveforms included in min-max envelope
Hi-Res	Real-time boxcar averaging reduces random noise and increases resolution
Waveform Database	Accumulates a waveform database that provides a three-dimensional array of amplitude, time, and counts
FastFrame™ Acquisition	Acquisition memory divided into segments; maximum trigger rate >100,000 waveforms per second

Trigger System

Characteristic	Description
Sensitivity
Internal DC Coupled	0.35 div DC to 50 MHz increasing to 1 div at rated bandwidth
External (Auxiliary input)	400 mV from DC to 50 MHz increasing to 750 mV at 100 MHz
Main Trigger Modes	Auto, Normal, and Single
Trigger Sequences	Main, Delayed by Time, Delayed by Events. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time
Standard Trigger Types	Edge, Glitch, Runt, Window, Width, Transition Time, Timeout, Pattern, Video, State, Setup/Hold
A Event and Delayed B Event Trigger Types
A Event	All above types
Delayed B Event	Edge
Communications-related Triggers (Requires Option SM)	Support for AMI, HDB3, BnZS, CMI, MLT3, and NRZ encoded communications signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to standard
Trigger Level Range
Any Channel	±10 divisions from center of screen
External (Auxiliary input)	±8 V
Line	Fixed at 0 V
Trigger Coupling	DC, AC (attenuate <60 Hz), HF reject (attenuate >30 kHz) LF reject (attenuates <80 kHz) Noise reject (reduce sensitivity)
Trigger Holdoff Range	1.5 μs to 12 s maximum

Trigger Modes

Mode	Description
Edge	Positive or negative slope on any channel or front-panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject, and LF reject
Video	Trigger on NTSC, PAL, SECAM, analog HDTV, and nonstandard video formats
Glitch	Trigger on or reject glitches of positive, negative, or either polarity. Minimum glitch width is 1.0 ns with 200 ps resolution
Width	Trigger on width of positive or negative pulse either within or out of selectable time limits ranging from 1 ns to 1 s with 200 ps resolution
Runt	Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Event can be time or logic qualified (logic on 4-channel models only)
Window	Trigger on an event that enters or exits a window defined by two user-adjustable thresholds. Event can be time or logic qualified (logic on 4-channel models only)
Timeout	Trigger on an event which remains high, low, or either, for a specified time period, selectable from 1 ns to 1 s with 200 ps resolution
Transition	Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative, or either
Setup/Hold	Trigger on violations of both setup time and hold time between clock and data present on any two input channels
Pattern	Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as High, Low, or Don't Care
State	Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge
Comm (Requires Option SM)	Support for AMI, HDB3, B3ZS, B6ZS, B8ZS, CMI, NRZ, and MLT3 encoded communication signals. Select among isolated positive or negative one, zero pulse form, or eye patterns as applicable to standard
Trigger Delay by Time	16 ns to 250 s
Trigger Delay by Events	1 to 10,000,000 events

Waveform Measurements

Characteristic	Description
Automatic Measurements	53, of which 8 can be displayed on-screen at any one time
Amplitude related	Amplitude, High, Low, Maximum, Minimum, Peak-to-Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot
Time related	Rise Time, Fall Time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay
Combination	Area, Cycle Area, Phase, Burst Width
Histogram related	Waveform Count, Hits in Box, Peak Hits, Median, Maximum, Minimum, Peak-to-Peak, Mean (μ), Standard Deviation (σ), μ ± 1σ, μ ± 2σ, μ ± 3σ
Communications related	Extinction Ratio (abs, %, dB), Eye Height, Eye Width, Eye Top, Eye Base, Crossing %, Jitter (P-P, RMS, 6σ), Noise (P-P, RMS), Signal/Noise Ratio, Cycle Distortion, Q-factor
Measurement Statistics	Mean, Min, Max, Standard Deviation, Population
Reference Levels	User definable for each of the eight measurements
Histograms	Vertical or horizontal with linear or log scaling
Gating	Isolate the specific occurrence within an acquisition to take measurements on
Cursors	Horizontal Bars, Vertical Bars, Waveform, and Screen

Waveform Processing/Math

Characteristic	Description
Arithmetic	Add, subtract, multiply, and divide waveforms
Algebraic Expressions	Define extensive algebraic expressions including waveforms, scalars, user-adjustable variables, and results of parametric measurements e.g. (Integral (Ch1 – Mean(Ch1)) × 1.414 × VAR1)
Math Functions	Average, Invert, Integrate, Differentiate, Square Root, Exponential, Log 10, Log e, Abs, Ceiling, Floor, Min, Max, Sin, Cos, Tan, ASin, ACos, ATan, Sinh, Cosh, Tanh
Frequency Domain Functions	Spectral magnitude and phase, real and imaginary spectra
Vertical Units	Magnitude: Linear, dB, dBm Phase: degrees, radians, group delay
Window Functions	Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential
Limit Testing	Compare live waveforms against a known “golden” reference waveform with user-defined vertical and horizontal tolerances

Display Characteristics

Characteristic	Description
Display Type	10.4 in. Liquid-crystal active-matrix color display
Touch Screen	Standard on TDS5054B and TDS5104B. Optional touch screen on TDS5034B
Display Resolution	640 horizontal × 480 vertical pixels
Waveform Styles	Vectors, Dots, Intensified Samples, Variable Persistence, Infinite Persistence
Display Format	YT, XY, XYZ
Color Palettes	Individual color palettes for Record View and FastAcq/WfmDB modes include Normal, Green, Gray, Temperature, Spectral, and User Defined

Computer System and Peripherals

Characteristic	Description
Operating System	Windows 2000
CPU	Intel Celeron Processor, 2.0 GHz
PC System Memory	512 MB
Internal Hard Disk Drive	≥80 GB capacity
CD-RW Drive	Side-panel CD-RW drive, ≥24x read and write speed
Mouse	Optical wheel mouse, USB interface

OpenChoice Features

Characteristic	Description
TekVISA	Application Programmers Interface (API) for Windows developers. Documentation includes descriptions and samples of programming test and measurement applications on the unit in Visual BASIC, C, and C++
TekVISA Control (TVC)	Active controls to make access to TekVISA easy for integration into Microsoft Windows applications
VXI-11 Server	An Application Programmers Interface (API) for LAN connectivity from non-Windows environments
Plug-and-Play Drivers	Provides support to run National Instrument's LabVIEW and LabWindows on an external PC connected to a TDS5000B or on the oscilloscope itself. Instrument drivers are version specific and might not support the version of your software development tools
IVI Drivers	Provides support for new and existing program environments utilizing the IVI instrumentation standard, such as LabVIEW, LabWindows/CVI, MATLAB, Visual BASIC, and C/C++. Instrument drivers are version specific and might not support the version of your software development tools
Excel and Word Toolbars	Provides direct access to screen images, waveform data, and measurements on the oscilloscope from a toolbar in Excel and/or Word
Report Generator	Enables the ability to design and create customized report templates that extract the oscilloscope's waveforms, settings, measurements, and other on-screen information with a click of the mouse

Input/Output Ports

Port	Description
Auxiliary Input	Front-panel BNC connector. Trigger level range is adjustable from +8 V to –8 V. The maximum input voltage is ±20 V (DC + peak AC) and input resistance is ≥1.5 kΩ
Probe Compensator Output	Front-panel pins. Amplitude 1 V ±1% into a ≥10 kΩ load, frequency 1 kHz ±5%
Analog Signal Output	Rear-panel BNC connector, provides a buffered version of the signal that is attached to the Channel 3 input (4-channel models only). Amplitude: 50 mV/div ±20% into a 1 MΩ load, 25 mV/div ±20% into a 50 Ω load. Bandwidth (typical): 100 MHz into a 50 Ω load
Auxiliary Output Levels	Rear-panel BNC connector, provides a TTL-compatible, negative-polarity pulse when the oscilloscope triggers
External Reference In	Rear-panel BNC connector. 9.8 MHz to 10.2 MHz
Parallel Port	IEEE 1284, DB-25 connector
Audio Ports	Miniature phone jacks for stereo microphone input and stereo line output
USB Port	Four USB 2.0 ports allows connection or disconnection of USB keyboard and/or mouse while oscilloscope power is on
Keyboard Port	PS-2 compatible
Mouse Port	PS-2 compatible
LAN Port	RJ-45 connector, supports 10BASE-T and 100BASE-T
Serial Port	DB-9 COM1 port
Video Port	DB-15 female connector; connect a second monitor to use dual-monitor display mode. Supports basic requirements of PC99 specification and display resolutions up to 1,920 × 1,440
GPIB Port	IEEE 488.2 standard, can be configured for talk/listen or controller mode
Oscilloscope VGA Video Port	DB-15 female connector, connect to show the oscilloscope display on an external monitor or projector

Power Source

Characteristic	Description
Power	100 to 240 V_RMS ±10%, 47 to 63 Hz; CAT II, or 115 V_RMS ±10%, 360 to 440 Hz
Power Consumption	<220 W

Physical Characteristics

Configuration	Benchtop	Rackmount	Benchtop	Rackmount
Dimensions	mm		in.
Height	361	267	11.2*¹	10.5
Width	447	483	17.6	19
Depth	288	231*²	11.35	9.1*²
Weight	kg		lb.
Net	11.23	13.49	24.75	29.75
Shipping	25.63	—	56.5	—
Cooling
Cooling Clearance	76 mm required on left side		3 in. required on left side

*¹ Does not include accessory pouch.

*² From rack mounting rear to back of instrument.

Environmental

Characteristic	Description
Temperature
Operating	+5 °C to +45 °C
Nonoperating	–20 °C to +60 °C without diskette in floppy drive
Humidity
Operating	20% to 80% relative humidity with a maximum wet bulb temperature of +29 °C at or below +45 °C, noncondensing. Upper limit derates to 30% relative humidity at +45 °C
Nonoperating	Without diskette in floppy disk drive. 5% to 90% relative humidity with a maximum wet bulb temperature of +29 °C at or below +60 °C, noncondensing. Upper limit derates to 20% relative humidity at +60 °C
Altitude
Operating	10,000 ft. (3,048 m)
Nonoperating	40,000 ft. (12,190 m)
Random Vibration
Operating	0.1 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total
Nonoperating	2.0 G_RMS from 5 to 500 Hz, 10 minutes each axis, 3 axes, 30 minutes total
Regulatory Certifications
Electromagnetic compatibility	89/336/EEC
Safety	UL61010, CSA-22.2 No. 1010.1, EN61010-1, IEC61010-1