TDS7104

索取报价

概述

技术指标

此产品已经停止销售，请与我们联系获得更多帮助。

Characteristics

Vertical System

	TDS7054	TDS7104	TDS7154	TDS7254	TDS7404
Input Channels	4	4	4	4	4
Analog Bandwidth (–3 dB)	500 MHz	1 GHz	1.5 GHz	2.5 GHz	4 GHz
Calculated Rise Time 10 mV/div to 1 V/div	800 ps	400 ps	240 ps	160 ps	100 ps
Hardware Bandwidth Limits	250 MHz or 20 MHz		Requires TCA-1 MEG
Input Coupling	AC, DC, Gnd		DC, Gnd
Input Impedance	1 MΩ ±0.5% or 50 Ω ±1%		50 Ω ±2.5%
Input Sensitivity, 1 MΩ	1 mV/div to 10 V/div		—
Input Sensitivity, 50Ω	1 mV/div to 1 V/div		2 mV/div to 1 V/div
Vertical Resolution	8-Bit (>11-Bit with averaging)		8-Bit (>11-Bit with averaging)
Max Input Voltage, 1 MΩ	±150 V CAT I Derate at 20 dB/decade to 9 V_RMS above 200 kHz		—
Max Input Voltage, 50Ω	5 V_RMS, with peaks less than ±30 Volts		Determined by TekConnect™ Accessory
DC Gain Accuracy	1%		±(2% + (2% * offset))
Offset Range
	1 mV/div to 100 mV/div: ±1 V		2 mV to 50 mV/div: ±0.5 V
	101 mV/div to 1 V/div: ±10 V		50.5 mV to 99.5 mV: ±0.25 V
	1.01 V/div to 10 V/div: ±100 V		100 mV to 500 mV: ±5 V 505 mV to 1 V/div: ±2.5 V
Channel-to-channel Isolation Any Two Channels at Equal Vertical Scale Settings	≥100:1 at 100 MHz and ≥30:1 at the Rated Bandwidth		≥100:1 at <2.5 GHz and ≥40:1 at 4 GHz

Note: Typical system bandwidth of TDS7404 with P7240: 4 GHz.

Note: Typical system bandwidth of TDS7404 with P7330: 3.5 GHz.

Time Base System

	TDS7054/TDS7104	TDS7154/TDS7254/TDS7404
Time Base Range	200 ps/div to 40 s/div	50 ps to 10 s/div
Time Base Delay Time Range	16 ns to 250 s	16 ns to 250 s
Channel-to-channel Deskew Range	±25 ns	±25 ns
Delta Time Measurement Accuracy	±((0.06/sample rate) + (15 ppm * reading)) RMS	±((0.06/sample rate) + (2.5 ppm * reading)) RMS
Trigger Jitter (RMS)	8 psRMS (typical) 6 ps_RMS (typical)
Long Term Sample Rate and Delay Time Accuracy	±15 ppm over ≥1 ms interval	±2.5 ppm over any ≥100 ms interval

Acquisition System

Real-time Sample Rates	TDS7054	TDS7104	TDS7154/TDS7254/TDS7404
1 channel (max)	5 GS/s	10 GS/s	20 GS/s
2 channels (max)	5 GS/s	5 GS/s	10 GS/s
3 to 4 channels (max)	2.5 GS/s	2.5 GS/s	5 GS/s
Equivalent Time Sample Rate (max)	250 GS/s	250 GS/s	1 TS/s
Maximum Record Length per Channel with Standard Memory	2 M (1-CH.), 1 M (2-CH.), 500 k (4-CH.)
with Memory Opt. 2M	8 M (1-CH.), 4 M (2-CH.), 2 M (4-CH.)
with Memory Opt. 3M	16 M (1-CH.), 8 M (2-CH.), 4 M (4-CH.)
with Memory Opt. 4M			32 M (1-CH.), 16 M (2-CH.), 8 M (4-CH.)

Maximum Duration at Highest Real-time Resolution (1-CH)

	TDS7054	TDS7104	TDS7154/TDS7254/TDS7404
Time Resolution (Single-shot)	200 ps (5 GS/s)	100 ps (10 GS/s)	50 ps (20 GS/s)
Max Duration with Standard Memory	400 μs	200 μs	100 μs
Max Duration with Opt. 2M	1.6 ms	800 μs	400 μs
Max Duration with Opt. 3M	3.2 ms	1.6 ms	800 μs
Max Duration with Opt. 4M			1.6 ms

Acquisition Modes

	TDS7054/TDS7104	TDS7154/TDS7254/TDS7404
FastAcq Acquisition	FastAcq optimizes the instrument for analysis of dynamic signals and capture of infrequent events
Maximum FastAcq Waveform Capture Rate	>200,000 wfms/sec	>400,000 wfms/sec
Waveform Database (requires Option SM)	Accumulate Waveform Database providing three-dimensional array of amplitude, time and counts
Sample	Acquire sampled values
Peak Detect	Captures narrow glitches at all real-time sampling rates
Minimum Peak Detect Pulse Width	≤1 ns	400 ps
Averaging	From 2 to 10,000 waveforms included in average
Envelope	From 2 to 2x10⁹ waveforms included in min-max envelope
Hi-res	Real-time boxcar averaging reduces random noise and increases resolution
FastFrame™ Acquisition	Acquisition memory divided into segments; maximum trigger rate >160,000 waveforms per second. Time of arrival recorded with each event

Trigger System

	TDS7054	TDS7104	TDS7154/TDS7254/TDS7404
Sensitivity
Internal DC Coupled	0.35 div DC to 50 MHz increasing to 1 div at 500 MHz	0.35 div DC to 50 MHz increasing to 1 div at 1 GHz	0.35 div DC to 50 MHz increasing to 1.5 div at 3 GHz TDS7404: 2.7 div at 4 GHz (typical)
External (Auxiliary Input)	400 mV from DC to 50 MHz increasing to 750 mV at 100 MHz	250mV from DC to 50 MHz increasing to 500mV at 100 MHz	250mV from DC to 50 MHz increasing to 350mV at 500 MHz
Main Trigger Modes	Auto, Normal and Single
Trigger Sequences	Main, Delayed by Time, Delayed by Events. All sequences can include separate horizontal delay after the trigger event to position the acquisition window in time
Trigger Characteristics
Standard Trigger Types	Edge, Glitch, Runt, Width, Transition Time, Timeout, Pattern, State, Setup/Hold
Communications-related	Support for AMI, HDB3, BnZS, CMI, MLT3 and NRZ encoded communications signals.
Triggers (requires Option SM)	Select among isolated positive or negative one, zero pulse form or eye patterns as applicable to standard.
Serial Pattern Trigger (requires Option ST)			32-Bit serial word recognizer, bits specified in binary (high, low, don’t care) or hex format. Trigger on NRZ-encoded data up to 1.25 GBaud.
Trigger Level Range
Internal	±12 divisions from center of screen
External (Auxiliary In)	±8 V
Line	fixed at 0 V
Trigger Coupling	DC, AC (attenuates <60 Hz), HF Rej (attenuates >30 kHz), LF Rej (attenuates <80 kHz), Noise Reject (reduces sensitivity)
Trigger Holdoff Range	250 ns minimum to 12 s maximum

Trigger Modes

Edge	Positive or negative slope on any channel or front panel auxiliary input. Coupling includes DC, AC, noise reject, HF reject and LF reject.
Glitch	Trigger on or reject glitches of positive, negative or either polarity. Minimum glitch width is 1.0 ns with 200 ps resolution.
Width	Trigger on width of positive or negative pulse either within or out of selectable time limits (1 ns to 1 s).
Runt	Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again. Optional time qualification.
Timeout	Trigger on an event which remains high, low or either, for a specified time period, selectable from 1 ns to 1 s with 200 ps resolution.
Transition	Trigger on pulse edge rates that are faster or slower than specified. Slope may be positive, negative or either.
Setup/Hold	Trigger on violations of both setup time and hold time between clock and data present on any two input channels.
Pattern	Trigger when pattern goes false or stays true for specified period of time. Pattern (AND, OR, NAND, NOR) specified for four input channels defined as HIGH, LOW or Don’t Care.
State	Any logical pattern of channels (1, 2, 3) clocked by edge on channel 4. Trigger on rising or falling clock edge.
Trigger Delay by Time	16 ns to 250 seconds.
Trigger Delay by Events	1 to 10,000,000 Events.

Waveform Measurements

Amplitude	Amplitude, High, Low, Maximum, Minimum, Peak to Peak, Mean, Cycle Mean, RMS, Cycle RMS, Positive Overshoot, Negative Overshoot.
Time	Rise time, Fall time, Positive Width, Negative Width, Positive Duty Cycle, Negative Duty Cycle, Period, Frequency, Delay.
Combination	Area, Cycle Area, Phase, Burst Width.
Histogram-related	Waveform count, Hits in box, Peak hits, Median, Maximum, Minimum, Peak to Peak, Mean (μ), Standard Deviation (σ), μ+1σ, μ+2σ, μ+3σ.

Waveform Processing/Math

Algebraic Expressions	Define extensive algebraic expressions including waveforms, scalars and results of parametric measurements e.g. (Integral (CH.1-Mean(CH.1))*1.414).
Arithmetic	Add, subtract, multiply, divide waveforms and scalars.
Relational	Boolean result of comparison >, <, >=, <=, ==, !=.
Calculus	Integrate, differentiate.
Frequency Domain Functions	Spectral magnitude and phase, real and imaginary spectra.
Vertical Units	Magnitude: Linear, dB, dBm; Phase: Degrees, radians.
Window Functions	Rectangular, Hamming, Hanning, Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2, Tek Exponential.
Waveform Definition	As arbitrary math expression.

Display Characteristics

Display Type	Liquid crystal active-matrix color display.
Display Size
Width:	211.2 mm (8.32 in.);
Height:	158.4 mm (6.24 in.);
Diagonal:	264 mm (10.4 in.).
Display Resolution	640 horizontal x 480 vertical pixels.
Waveform Styles	Vectors, Dots, Variable Persistence, Infinite Persistence.

Computer System and Peripherals

CPU	Intel Celeron processor, 850 MHz.
PC System Memory	512 MB.
Hard Disk Drive	Rear-panel, removable hard disk drive, 20 GB capacity.
Floppy Disk Drive	Front-panel 3.5 in floppy disk drive, 1.44 MB capacity.
CD-R/W Drive	Rear-panel CD-R/W drive with CD creation software application.
Mouse	Logitech thumb wheel model included, USB interface.
Keyboard	For small keyboard (fits in pouch); PS-2 interface. Order 118-9402-00 For full-size keyboard; USB interface and hub. Order 119-6297-00

Input/Output Ports

Probe Compensator Output	Front panel BNC connector, requires Probe Cal-Deskew Fixture (included) for probe attachment. Amplitude 200 mV ±20% into a ≥50 Ω load, frequency 1 kHz ±5%.
Analog Signal Output Amplitude	Front-panel BNC connector, provides a buffered version of the signal that is attached to the Ch 3 input when Ch 3 is selected as trigger source. 20 mV/div ±20% into a 1 MΩ load, 10 mV/div ±20% into a 50 Ω load.
Analog Signal Output Bandwidth, Typical	TDS7054, TDS7104: 100 MHz into a 50 Ω load. TDS7154/TDS7254/TDS7404: 1 GHz into a 50 Ω load.
External Time Base Reference In	Rear-panel BNC connector, time base system can phase-lock to external 10 MHz reference.
Time Base Reference Out	Rear-panel BNC connector, accepts TTL-compatible output of internal 10 MHz reference oscillator.
Auxiliary Output Levels	Front-panel BNC connector, provides a TTL-compatible, polarity switchable pulse when the oscilloscope triggers.
Parallel Port	IEEE 1284, DB-25 connector.
Audio Ports	Miniature phone jacks for stereo microphone input and stereo line output.
USB Port	Allows connection or disconnection of USB keyboard and/or mouse while oscilloscope power is on.
Keyboard Port	PS-2 compatible.
Mouse Port	PS-2 compatible.
LAN Port	RJ-45 connector, supports 10Base-T and 100Base-T.
Serial Port	DB-9 COM1 port.
SVGA Video Port	DB-15 female connector; connect a second monitor to use dual-monitor display mode. Supports basic requirements of PC99 specifications.
GPIB Port	IEEE 488.2 standard.
Scope VGA Video Port	DB-15 female connector, 31.6 kHz sync, EIA RS-343A compliant, connect to show the oscilloscope display, including live waveforms on an external monitor or projector.

Power Source

Power

100 to 240 V_RMS, ±10%, 50/60 Hz;

115 V_RMS ±10%, 400 Hz;

CAT II, <300 W (450 VA).

Physical Characteristics

Benchtop Configuration

Dimensions	mm	in.
Height	277	10.9
Width	455	17.9
Depth	425	16.75
Weight	kg	lb.
Net	18	39
Shipping	37	80

Rackmount Configuration

Dimensions	mm	in.
Height	277	10.5
Width	502	19.75
Depth	486	19.125
Weight	kg	lb.
Net	19	41
Kit	5.6	12.25

Mechanical

Cooling – Required

Clearance	mm	in.
Top 0 or	>76	0 or >3
Bottom	0	0
Left side	76	3
Right side	76	3
Front	0	0
Rear	0	0

Environmental

Temperature
Operating	0ºC to +50ºC, excluding floppy disk and CD-R/W drives; +10ºC to +45ºC, including floppy disk and CD-ROM drives.
Nonoperating	–22ºC to +60ºC.
Humidity
Operating	20% to 80% relative humidity with a maximum wet bulb temperature of +29ºC at or below +50ºC, noncondensing. Upper limit derated to 25% relative humidity at +50ºC.
Nonoperating	With no diskette in floppy disk drive. 5% to 90% relative humidity with a maximum wet bulb temperature of +29ºC at or below +60ºC, noncondensing. Upper limit derated to 20% relative humidity at +60ºC.
Altitude
Operating	10,000 ft. (3,048 m).
Nonoperating	40,000 ft. (12,190 m).
Random Vibration
Operating	0.000125 G2/Hz from 5 to 350 Hz, –3 dB/octave from 350 to 500 Hz, 0.0000876 G2/Hz at 500 Hz. Overall level of 0.24 G_RMS.
Nonoperating	0.0175 G2/Hz from 5 to 100 Hz, –3 dB/octave from 100 to 200 Hz, 0.00875 G2/Hz from 200 to 350 Hz, –3 dB/octave from 350 to 500 Hz, 0.006132 G2/Hz at 500 Hz. Overall level of 2.28 G_RMS.
Electromagnetic Compatibility	89/336/EEC.
Safety	UL 3111-1, CSA1010.1, EN61010-1, IEC 61010-1.