下载
下载

下载手册、产品技术资料、软件等:

下载类型
型号或关键字

MDO3000

MDO3000 混合域示波器拥有多达六种仪器,包括频谱分析仪、函数发生器等选件,让您通过一台示波器就能捕获模拟信号、数字信号和 RF 信号。随着设计挑战的不断变化,您甚至可以添加仪器、分析功能并升级带宽。

基本价格
US $3,770 - US $15,600
购买/报价 有问题?现在就聊
带宽

高达 1 GHz

记录长度

10 M 点

模拟通道

24

采样率

高达 5 GS/s

 

不止是功能强大的示波器。

MDO3000系列分解图

当今工程领域的主流是多核处理器、串行总线和无线接口。 MDO3000 的核心是有基本频谱分析仪和数字电压表的成熟可靠的泰克示波器。 然后,您可以按照测试需求自定义。 添加 16 个逻辑通道、一个 50 MHz 任意波形/函数发生器、协议分析和一个扩展式 3 GHz 频谱分析仪,可帮助满足当前与未来的复杂设计的要求。

特点

  • 采用 125 种触发组合的获奖示波器
  • 通过 Wave Inspector® 控件达到 10 M 点记录长度
  • 标配基本频谱分析仪
  • 根据测试需求添加仪器和功能

准确测量很重要

MDO4000系列,提供准确的测量结果

简单来说,MDO3000 系列示波器旨在实现准确的测量。 在其他许多仪器仅提供低分辨率显示数据时,MDO3000 测量实际采集数据,可以无比通畅地查看您的设计。 事实上,我们对于 MDO3000 提供的技术规格非常自信,让您在测量时拥有十足把握。 毕竟,测量精度影响设计完整性。 为什么要采用不够准确的设备?

非常具有性价比的探头:免费提供。

MDO3000系列,免费提供性价比最高的探头

作为测量信号路径中的关键元件,探头不容忽视。 在购买 MDO3000 时,您将免费获得此探头。 由于拥有负载 (3.9 pF) 和可匹配您示波器的高带宽,TPP 系列探头将是您日常使用的随身探头。

特点

  • TPP 系列探头为标配,每条模拟通道一只
  • 3.9 pF 的电容性探头负载
  • 250 MHz、500 MHz 或 1 GHz 探头带宽,可满足示波器的带宽

不是 RF 专家也可以轻松完成无线测量

MDO3000系列透视

无线通信与 EMI 注意事项是否让您感到烦躁? 也许,您是一位 RF 专家,需要一台能够进行时域和频域测量的示波器? 不管怎样,带内置频谱分析仪的 MDO3000 示波器均能胜任任务。 与那些会提供 FFT“频谱分析”的其他示波器不同,只有 MDO3000 才内置真正的频谱分析仪,供您在可达 3 GHz 频率的环境下进行 RF 测量,而无需离开示波器。

特点

  • 基本频谱分析仪,标配
  • 3 GHz 频谱分析仪可以升级
  • 真正集成的频谱分析仪硬件

意外发生。 确保您受到保护。

我们拥有业内独具优势的意外损坏保护的计划。 是的,其中包括屏幕损坏、溢出、安装架损坏、静电放电或电子过载事件。 使用我们的“全面呵护计划”降低意外维修或更换成本。 观看视频或单击下方了解详情。

了解详情

型号 模拟带宽 采样率 记录长度 模拟通道 数字通道数 频谱分析仪 函数发生器输出 报价
MDO3012 100 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $3,770
配置和报价
MDO3014 100 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $4,490
配置和报价
MDO3022 200 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $4,500
配置和报价
MDO3024 200 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $5,020
配置和报价
MDO3032 350 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $7,770
配置和报价
MDO3034 350 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $9,340
配置和报价
MDO3052 500 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $9,860
配置和报价
MDO3102 1 GHz 5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $11,700
配置和报价
MDO3054 500 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $12,600
配置和报价
MDO3104 1 GHz 5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $15,600
配置和报价
价格:价格如有变更,恕不另行通知。
型号 模拟带宽 采样率 记录长度 模拟通道 数字通道数 频谱分析仪 函数发生器输出 报价
MDO3012 100 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $3,770
配置和报价
MDO3014 100 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $4,490
配置和报价
MDO3022 200 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $4,500
配置和报价
MDO3024 200 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $5,020
配置和报价
MDO3032 350 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $7,770
配置和报价
MDO3034 350 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $9,340
配置和报价
MDO3052 500 MHz 2.5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $9,860
配置和报价
MDO3102 1 GHz 5 GS/s 10 M 点 2 16(选配) 最高 3 GHz

1 条(可选)

US $11,700
配置和报价
MDO3054 500 MHz 2.5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $12,600
配置和报价
MDO3104 1 GHz 5 GS/s 10 M 点 4 16(选配) 最高 3 GHz

1 条(可选)

US $15,600
配置和报价
价格:价格如有变更,恕不另行通知。
  泰克
MDO3000
泰克
MDO4000C
Keysight
3000T
LeCroy
WaveSurfer 3000
R&S
RTM2000
带宽 100 MHz 至 1 GHz 200 MHz 至 1 GHz 100 MHz 至 1 GHz 200 MHz 至 750 MHz 200 MHz 至 1 GHz
可升级带宽
模拟通道 2 或 4 4 2 或 4 2 或 4 2 或 4
模拟采样率 高达 5 GS/s 高达 5 GS/s 高达 5 GS/s 高达 4 GS/s 高达 5 GS/s
标配记录长度(所有通道) 10 M 20 M 2 M 10 M 10 M
集成任意波形/函数发生器 50 MHz(可选) 50 MHz(可选) 20 MHz(可选) 25 MHz(可选) --
集成逻辑通道 (MSO) 16 条(可选) 16 条(可选) 16 条(可选) 16 条(可选) 16 条(可选)
集成硬件频谱分析仪 最高 3 GHz(可选) 最高 6 GHz(可选) -- -- --
模拟、数字和 RF 通道的全同步 -- -- -- --
标准探头 最高 1 GHz 无源探头 最高 1 GHz 无源探头 最高 500 MHz 无源探头 最高 500 MHz 无源探头 最高 500 MHz 无源探头
标准保修 3 年 3 年 3 年 3 年 3 年

嵌入式串行总线触发、解码和分析

Thumbnail

单个串行总线信号通常包括地址、控制、数据和时钟信息;很难单独挑出感兴趣的事件。 MDO3000 系列示波器的串行应用模块将示波器变为一款利用自动触发、解码和搜索来调试串行总线的强大工具。

特点

  • I2C、SPI、RS-232 / 422 / 485 / UART
  • CAN/CAN FD、LIN、FlexRay
  • I2S/LJ/RJ/TDM
  • MIL-STD-1553、USB

功率测量和分析

Thumbnail

随着对能源效率的要求越来越高,设计师和测试仪器都面临着新的挑战。 待机功率限制、更高的开关速度和信号范围和更低漏电流的半导体器件,正在将测试条件推向新的高度。 MDO3000 可提供电源测试解决方案来应对这些不断变化的要求。

特点

  • 开关设备的功率损耗测量
  • 纹波和噪声的测量和分析
  • 检定功率半导体器件
  • 调试有源功率因数校正电路

电磁干扰 (EMI) 和电磁兼容性 (EMC)

Thumbnail

执行设计 EMI/EMC 测试时,始终存在失败风险;从而导致进度和预算问题。 内置频谱分析仪的 MDO3000 可让您在实验室中执行预一致性测试,可显著提高完整 EMI 一致性测试第一次就成功通过的概率。

汽车总线 – CAN/CAN FD 触发、解码和分析

Thumbnail

当今汽车的技术要求所要求的电子器件和系统比以往更复杂、更敏感。 泰克 MDO3000 是六合一仪器,旨在帮助应对这些先进技术的测试和验证挑战。 现在一台仪器可用于以下用途:

  • 调试和验证 CAN FD、CAN、LIN 和 FlexRay
  • 混合动力/电动车辆的大功率测试
  • 验证车载无线系统
  • 新器件评估(MEMS 传感器、LED 驱动器、LED

 

产品技术资料 软件包 / 软件选件 描述 配置和报价
附件 119414600
产品技术资料 描述
视图 产品技术资料 探头套件;RF 测量,近场探头套件,无源,手持式
附件 119660900
产品技术资料 描述
视图 产品技术资料 天线;塑料护套,带 BNC 连接器,KD4 VHF;未调谐,塑料帽粘上
附件 ACD3000
产品技术资料 描述
视图 产品技术资料 MDO3000 系列示波器用软携带包
附件 HCTEK4321
产品技术资料 描述
附件 MDO3AFG
产品技术资料 描述
视图 产品技术资料 为 MDO3000 系列示波器添加 1 通道任意函数发生器
附件 MDO3MSO
产品技术资料 描述
视图 产品技术资料 为 MDO3000 系列示波器添加 16 个带 P6316 逻辑探头的数字通道
附件 MDO3SA
产品技术资料 描述
视图 产品技术资料 在 MDO3000 系列示波器上将频谱分析仪输入频率增加至 3GHz
附件 P6316
产品技术资料 描述
视图 产品技术资料 MSO 探头;16 通道通用探头
附件 RMD3000
产品技术资料 描述
视图 产品技术资料 机架安装套件
附件 TEK-USB-488
产品技术资料 描述
USB 至 IEEE488 (GPIB) 通信适配器,适用于 USBTMC-USB488 兼容泰克仪器
附件 TPA-BNC
产品技术资料 描述
探头适配器,从 TekProbe-BNC 至 TekVPI
附件 TPA-N-PRE
产品技术资料 描述
外部预放大器,TPA 连接器,SMA 输入
附件 TPA-N-VPI
产品技术资料 描述
视图 产品技术资料 探头适配器,从 Type-N 连接器至 TekVPI
产品技术资料 附件 描述
119414600 探头套件;RF 测量,近场探头套件,无源,手持式
119660900 天线;塑料护套,带 BNC 连接器,KD4 VHF;未调谐,塑料帽粘上
ACD3000 MDO3000 系列示波器用软携带包
HCTEK4321 硬提包
MDO3AFG 为 MDO3000 系列示波器添加 1 通道任意函数发生器
MDO3MSO 为 MDO3000 系列示波器添加 16 个带 P6316 逻辑探头的数字通道
MDO3SA 在 MDO3000 系列示波器上将频谱分析仪输入频率增加至 3GHz
P6316 MSO 探头;16 通道通用探头
RMD3000 机架安装套件
视图 产品技术资料 TEK-USB-488 USB 至 IEEE488 (GPIB) 通信适配器,适用于 USBTMC-USB488 兼容泰克仪器
视图 产品技术资料 TPA-BNC 探头适配器,从 TekProbe-BNC 至 TekVPI
视图 产品技术资料 TPA-N-PRE 外部预放大器,TPA 连接器,SMA 输入
TPA-N-VPI 探头适配器,从 Type-N 连接器至 TekVPI
Generate a Wide Range of Signals with the Integrated Arbitrary/Function Generator.
2m 31s
Debug Your Serial Buses in Seconds with the Integrated Protocol Analyzer.
2m 58s
The MDO3000 Mixed Domain Oscilloscope features six integrated instruments, including a spectrum analyzer, function generator and more, giving you the ability to capture analog, digital and RF sign...
56s
Perform Quick Measurements with the Integrated Digital Voltmeter.
1m 50s
Discover the exceptionally wide capture bandwidth of the integrated spectrum analyzer found in the MDO3000 Series Mixed Domain Oscilloscope.
3m 24s
Sometimes bad things happen to good scopes!  Ensure you've got it covered with a Total Product Protection plan from Tektronix, the only coverage plan available for test equipment with accident pro...
Find Elusive Signal Problems with the MDO3000 Mixed Domain Oscilloscope.
2m 39s
Monitor More of Your Design with the Integrated Logic Analyzer.
2m 48s
In this short video, we demo the CAN FD bus decoding process on the flexible MDO3000 oscilloscope. 
4m 28s
See a few everyday examples of engineering tasks you can do with this ultimate 6-in-1 integrated instrument.
6m 54s
Uncover Noise Sources and Debug Wireless with the Integrated Spectrum Analyzer.
3m
What probe interface does my oscilloscope have?
Oscilloscope series Probe interface CSA7000/CSA7000B TekConnect DPO2000 TekVPI DPO3000
常见问题 ID64251 26 Feb 2020
Measurement Data Logging with TekBench Oscilloscope Control Software
This application note describes how to use TekBench™ Software and a Tektronix oscilloscope to perform measurement data logging for evaluating a design’s reliability in a room temperature environment, such as a project laboratory.

文献编号: 61W-61442-0
应用指南 19 Feb 2020
KickStart Instrument Control Software Version 2.2.1 (Windows 10, 8, 7 compatible)
KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the abil

部件号: KICKSTART-2.2.1
Software 16 Feb 2020
KickStart Instrument Control Software Datasheet
KickStart Software simplifies what you need to know about your instrument so that in just minutes you can take the instrument out of the box and get real data on your device.  KickStart Software enables quick test setup and data visualization when us

文献编号: 1KW-60965-4
Datasheet 04 Feb 2020
MDO3000 FIRMWARE, V1.14
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158604
Software 04 Feb 2020
TEKVISA CONNECTIVITY SOFTWARE - V4.1.1
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various c

部件号: 066093811
Software 04 Feb 2020
TEKVISA CONNECTIVITY SOFTWARE, V4.0.4
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol. When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various

部件号: 066093809
Software 04 Feb 2020
TEKVISA Connectivity Software - V4.2.0
TekVISA is the Tektronix implementation of VISA (Virtual Instrument Software Architecture), an industry-standard communication protocol.When installed on a PC, TekVISA provides communication with instruments that are connected to the PC via various c

部件号: 066093812
Software 04 Feb 2020
Tektronix Toolbars for Microsoft Office 32 bit - V4.0.4
Tektronix Toolbars for Microsoft Office v4.0.4 provide toolbars (add-ins) for the 32 bit versions of Microsoft Excel and Microsoft Word. This version of Toolbars requires OpenChoice TekVISA v4.0.4 (Part Number 066093809) to be preinstalled on the PC

部件号: 066133202
Software 04 Feb 2020
MDO3000 FIRMWARE, V1.12
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158603
Software 04 Feb 2020
MDO3000 FIRMWARE - V1.26
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158609
Software 04 Feb 2020
MDO3K FIRMWARE RELEASE - v1.30
MDO3000 firmware update

部件号: 066158611
Software 04 Feb 2020
MDO3000 FIRMWARE, V1.18
This firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158605
Software 04 Feb 2020
MDO3000 FIRMWARE, V1.20
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158606
Software 04 Feb 2020
MDO3000 FIRMWARE - V1.24
This Firmware is an upgrade for all MDO3000 Series oscilloscopes.

部件号: 066158608
Software 04 Feb 2020
Tektronix Openchoice Desktop Application TDSPCS1 - v2.6
The Tektronix OpenChoice Desktop free application lets you capture oscilloscope screen images, waveform data, and settings from a Microsoft Windows computer. After installing the software, refer to the section “Connecting to a PC” in your instrument’

部件号: 066093914
Software 04 Feb 2020
ARBEXPRESS WAVEFORM CREATION AND EDITING SW, V3.1
ArbExpress is a waveform creation and editing tool for Tektronix AWG and AFG instruments. It provides an easy to use and efficient way to create and edit waveforms, transfer waveforms to and from Arbitrary Waveform Generators (AWG), and Arbitrary/Fun

部件号: 066146103
Software 04 Feb 2020
KickStart Instrument Control Software Version 2.1.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ab

部件号: KICKSTART-2.1.0
Software 04 Feb 2020
KickStart Instrument Control Software Version 2.2.0 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ab

部件号: KICKSTART-2.2.0
Software 04 Feb 2020
KickStart Instrument Control Software Version 2.1.1 (Windows 10, 8, 7 compatible)
"KickStart Software for the PC enables quick test setup and data visualization when using one or more instruments. Key Features • Save time by automating data collection of millions of readings. • Set up a multi-instrument test with the ab

部件号: KICKSTART-2.1.1
Software 04 Feb 2020
DPO2000, MSO2000, DPO3000 and DPO4000, MSO3000 and MSO4000, MDO3000 and MDO4000 and MDO3 IVI Driver - V1.5
The Tektronix MSO/DPO2000, MDO/MSO/DPO3000, MDO/MSO/DPO4000 and MDO3 IVI Driver is an IVI class-compliant driver. It complies with Scope Class specifications (IVI-4.1) as defined by the IVI foundation. An IVI class-compliant specific driver for an os

部件号: 066133104
Software 04 Feb 2020
Tektronix MDO3000 Series Oscilloscope
This demonstration guide takes you through a series of step-by-step demonstrations on how the MDO3000 Series oscilloscope helps simplify the debug of mixed signal designs with its powerful functionality and integrated test instruments. This oscill

文献编号: 48W-29903-0
操作方式指南 04 Feb 2020
SOLUTIONS FOR SCIENTIFIC AND ENGINEERING RESEARCH

文献编号: 55W_30503_2
手册 04 Feb 2020
3 Series MDO vs. MDO3000 Series
This fact sheet compares important specifications and features of the Tektronix 3 Series MDO Mixed Domain Oscilloscope to those of the Tektronix MDO3000 Series Oscilloscopes.

文献编号: 48W-61605-0
速查资料 04 Feb 2020
How to Use a Mixed Signal Oscilloscope to Test Digital Circuits
Learn how to set up a mixed signal oscilloscope and how use it in several applications including: triggering on pulse width violations, combining analog and digital waveforms to capture crosstalk, troubleshooting setup/hold violations, and checking a

文献编号: 3GT-24008-4
应用指南 04 Feb 2020
Identifying Setup and Hold Violations with a Mixed Signal Oscilloscope
Problems with setup and hold timing are among the most challenging to identify.  Mixed signal oscilloscopes (MSOs) are able to capture both analog and digital representations of signals, making them well-suited for identifying digital timing problems

文献编号: 55W-61095-0
应用指南 04 Feb 2020
Introduction to Video Measurements
In this application note, we demonstrate using a MSO/DPO5000, MDO/MSO/DPO4000 and MDO/MSO/DPO3000 Series Oscilloscope to make a variety of video measurements that are common in standard and high definition systems.

文献编号: 3GW-20975-2
应用指南 04 Feb 2020
Automated Frequency Response Measurement with AFG31000, MDO3000, and TekBench™ Instrument Control Software
This application note describes how to use TekBench™ Software and a Tektronix AFG31000 series arbitrary function generator and an MDO3000 oscilloscope to perform the automated frequency response measurement effortlessly within just a few steps.

文献编号: 48W-61517-0
应用指南 04 Feb 2020
Probing Techniques for Accurate Voltage Measurements on Power Supplies with Oscilloscopes
Making oscilloscope voltage measurements on power supplies is fundamental, but not without challenges. Much is  written on oscilloscopes, but probing techniques are often taken for granted. This application note focuses on probing and covers: Choos

文献编号: 51W-60161-3
应用指南 04 Feb 2020
Making Accurate Current Measurements on Power Supplies with Oscilloscopes
Accurately measuring current with oscilloscopes is essential for power supply design and general electronics. Learn how to measure current using shunt resistors and voltage probes, and how to use clamp-on current probes with your oscilloscope. Get ti

文献编号: 51W-60171-2
应用指南 04 Feb 2020
MDO3000 Spectrum Analyzer vs. Oscilloscope FFT Comparison Fact Sheet
Mixed Domain Oscilloscopes have built-in spectrum analyzers with a dedicated RF input for significantly higher dynamic range than an oscilloscope with FFT. This fact sheet compares the performance of the MDO3000’s built-in spectrum analyzer to common

文献编号: 48W-30079-2
速查资料 04 Feb 2020
MDO3000 Series vs. Keysight X3000T Series Oscilloscopes
This 2-page fact sheet compares the features and specifications of Tektronix MDO3000 Series Mixed Domain Oscilloscopes to Keysight X3000T Series oscilloscopes.

文献编号: 3GA-60137-0
竞争 04 Feb 2020
Accurate Measurements Matter
The MDO3000 Series scope is designed to make the most accurate measurements in the industry. While many other instruments only offer low-resolution display data, the MDO3000 takes measurements on actual acquisition data, providing an unrivaled view i

文献编号: 48W-60968-2
速查资料 04 Feb 2020
MDO3000 Series Product Selection and Comparison Guide
This guide helps with the selection and comparison process as you research the MDO3000. It explains key specifications for oscilloscopes, spectrum analyzers and arbitrary/function generators.  It also provides a comparison template.

文献编号: 48W-30076-0
选型指南 04 Feb 2020
MDO4000C and MDO3000 Series Comparison Fact Sheet
This fact sheet compares features and specifications of MDO4000C and MDO3000 Series mixed domain oscillscopes.

文献编号: 48W-30086-2
选型指南 04 Feb 2020
MDO3000 Oscilloscope Upgrade Fact Sheet
The MDO3000 Series Mixed Domain Oscilloscope lets you add capabilities as your needs change.  This fact sheet gives a quick overview of the upgrades available for the MDO3000.

文献编号: 48W-30148-1
速查资料 04 Feb 2020
MDO3000 Series Configuration Fact Sheet
Step by step guide to configure your MDO3000 for your application, in a handy two-page format.

文献编号: 48W-30033-1
速查资料 04 Feb 2020
MDO3000 Series vs. Agilent MSO/DSO3000 X-Series
This 2-page fact sheet compares the features and key specifications of the Tektronix MDO3000 Series oscilloscopes to the Agilent 3000 X-Series.

文献编号: 48W-30078-2
竞争 04 Feb 2020
MDO3000 Series vs. Agilent N9320B Spectrum Analyzer
Side-by-side comparison on key specifications, automated markers, plus highlights of the key features of  the MDO3000:Capture bandwidthSpectogram displayIntegration with scope, logic, and protocol analysis

文献编号: 48W-30244-0
竞争 04 Feb 2020
Power Supply Measurement and Analysis Primer
A power supply is a component, subsystem, or system that converts electrical power from one form to another; commonly from alternating current (AC) utility power to direct current (DC) power. The proper operation of electronic devices ranging from pe

文献编号: 55T-18412-6
入门手册 04 Feb 2020
Is the SA (Spectrum Analyzer) in the MDO3000 field upgradable?
Yes, the MDO3SA is field upgradable by customers. Any instrument can upgrade the SA input frequency to 3GHz using this quick process in the field. After inserting the SA app module in the MDO3000 the SA is enabled .The SA app module can be removed fr
常见问题 ID69321 15 Jan 2020
Can my oscilloscope operate on 400Hz power?
Most scopes have a wide range of operating voltages and frequencies, a full list can be found in the user manual of your specific oscilloscope. If you're having trouble finding your answer or can't find the manual, please call our Technical Support C
常见问题 ID63266 15 Jan 2020
When should I use MagniVu on my oscilloscope?
MagniVu allows you to have higher resolution to accurately determine edge placement on your digital data. It helps you to make precise timing measurements on digital edges. On the MSO/MDO4000/B/C and MSO5000/B Series, you can see up to 32 times more
常见问题 ID63886 15 Jan 2020
I downloaded and Installed OpenChoice Desktop, but it doesn't recognize my scope.
Refer to the Prerequisites.txt file available to download on the same page for OpenChoice desktop. Make sure you have all the prerequisites specified.    Prerequisites 1. PC equipped with  Microsoft Windows 7 32 Bit and 64 Bit OS, Windows 8.1 32 Bit
常见问题 ID474266 15 Jan 2020
What's included in the MDO3000 and MDO4000C DDU option? 
The Distribution Demo Unit (DDU) option on Tektronix oscilloscopes is an option provided to distributors for demoing scopes to customers with a set time limit before it expires. Questions arise about what's included in the MDO3000 and MDO4000C Series
常见问题 ID72196 15 Jan 2020
The data sheet for my oscilloscope says that the vertical input sensitivity is 1 mV/div to 10 V/div in 1 MΩ mode. But I turn the Vertical Scale control fully clockwise and I can only get down to 10 mV/div. What am I doing wrong?
You probably aren't doing anything wrong. But you do have a 10X probe attached to that channel, right? The 1 mV/div specs relate to the oscilloscope inputs. If the signal’s source impedance is relatively low (<< 1 MOhm), the signal’s frequenc
常见问题 ID58571 15 Jan 2020
Can the P6316, P6516, or P6616 logic probes be used interchangeably?
The simple answer is no they can't be used interchangeably. The front end of the logic channels are different so different logic probes are needed between the scopes.   For MSO2000/B, MSO3000, and MDO3000 Series oscilloscopes, only the P6316 logic
常见问题 ID59166 15 Jan 2020
How do I erase and declassify an MSO/DPO2000, MSO/DPO/MDO3000, and MSO/DPO/MDO4000 Series oscilloscope?
This example will show you how to declassify the MDO4000/B/C Series oscilloscope. This procedure also applies to the MSO/DPO4000/B, MSO/DPO/MDO3000, and the MSO/DPO2000/B series of oscilloscope.The first step in the declassification process is TekSec
常见问题 ID66231 15 Jan 2020
How do I set up an Ethernet bus decode?
Make sure your setup is prepared to decode, that you have the needed probes, scope options, test boards, etc. Once you have the options it's important to know how to use the options and probe your signal. To setup Ethernet bus decoding, turn on your
常见问题 ID64731 15 Jan 2020
Is the AFG (Arbitrary Function Generator) in the MDO3000 field upgradable?
Yes, the MDO3AFG is field upgradable by customers. The MDO3AFG is a "single-use" application module. This application module can enable the AFG which is already present in the instrument. After inserting the AFG app module in the MDO3000 the AFG is e
常见问题 ID69316 15 Jan 2020
If someone buys a MDO3000 with option R5 and after one year enables SA and AFG. Does the warranty option R5 apply to SA and AFG or do they have to purchase R5 for SA/AFG separately? 
Yes, all extended Service options, including R5, cover the specific MDO3000 instrument for which the option was purchased. Like product warranty, Service options are linked to a specific model and serial number.  Product warranty and extended Service
常见问题 ID69311 15 Jan 2020
How do I set up a I2C Bus Decode?
The procedure to set up a I2C bus decode and trigger is simple once you understand the basics. First you have to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the DAC as possible with good
常见问题 ID64756 15 Jan 2020
How do I use the arbitrary function generator on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the function generator capability on the MDO3000 mixed domain oscilloscope. The MDO3000 contains an integrated arbitrary function generator (or AFG) that can output predefined or user-de
常见问题 ID69276 15 Jan 2020
I recently registered our Tektronix oscilloscope, updated the firmware and am currently trying to activate the free DVM & Frequency Counter.  I don’t see any software downloads for activating the DVM. Am I doing something wrong, or looking in the wrong spot?
After you have registered your oscilloscope on Tek.com, you should have received an email with instructions.  The email is sent to the address you used to login to tek.com.  If you haven't received the email after registration: Check your spam folde
常见问题 ID468046 15 Jan 2020
What is included in the Tektronix Near Field Probe kit (Tek p/n 119-4146-00) and what are they used for?
The Tektronix 119-4146-00 Near Field Probe Set is intended to serve as a versatile aid for diagnostic testing of radiated emissions over a broad range of frequencies from below 100 kHz to above 1GHz.  The probe set consist of three (3) magnetic field
常见问题 ID64501 15 Jan 2020
Is the MDO3000 free video the same as the DPO3VID.
On our past MSO/DPO3000 Series products, we had an extended video analysis module.  Well, we have now made all that capability standard on the MDO3000. And the 500MHz models and below also have a native 75 Ohm input termination – the native impedanc
常见问题 ID781581 15 Jan 2020
Does Tektronix have a 12-bit oscilloscope?
Yes! Tektronix offers many different models of real-time oscilloscopes that provide 12-bit or greater vertical resolution for a variety of applications. Because many high-vertical-resolution oscilloscopes on the market have technical trade-offs such
常见问题 ID69266 15 Jan 2020
Which probes are compatible with oscilloscopes with the TekVPI probe interface?
There are a couple different types of TekVPI interfaces, one with a notch and one without. The notch was implemented later and was put in place because the front end was designed differently and communicates uniquely with those types of probes. Spe
常见问题 ID56226 15 Jan 2020
Why isn’t the TPP1000 (Tektronix Passive Probe 1GHz) compatible with my scope?
Short answer is that if your scope doesn’t have the notched key that allows the probe to connect, then the TPP probe requires a different termination resistance than what your scope can provide. Long answer is that traditionally, passive probes (i
常见问题 ID467701 15 Jan 2020
I could not find any information regarding the increase in bits in resolution for HiRes mode. Is there any information available?
The increase in bits in resolution depends on the decimation ratio.  The decimation ratio can be determined as follows:D = MFs / FsMFs is the maximum non-interleaved sampling frequency of the scope.  For example: 5 GS/s for the DPO4104B or 2.5 GS/s f
常见问题 ID55421 15 Jan 2020
Programing - How do I get a Screen Capture from DPO4000 scope using Python?
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the
常见问题 ID64791 15 Jan 2020
How do I utilize the measurement features on a DPO/MSO/MDO3000 and DPO/MSO/MDO4000 Series oscilloscope?
The Measurements are the same as the DPO/MSO2000 Series scopes. By going into the measurement menu you can add and remove up to 4 measurements. You can gate the measurements which allows you to only measure the part of the captured waveform that you
常见问题 ID64651 15 Jan 2020
How can I increase the measurement accuracy using automated measurements vs cursors?
While Cursors are quick and easy at approximating measurements, using the automated measurements can give you a much better and accurate measurement results. Here are some techniques to be successful in making accurate measurements. Always use automa
常见问题 ID62606 15 Jan 2020
How do I Set up a Military Standard 1553 serial bus decode?
For doing Military Standard 1553 bus decode Tektronix recommends using a DPO/MSO/MDO 2000 or higher series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus ch
常见问题 ID64776 15 Jan 2020
Is the MDO3000 DVM the same as making an analog channel waveform measurement?
No, the MDO3000 uses a DVM IC that takes AC+DC RMS, DC and AC RMS measurements from signal on the respective channel inputs.
常见问题 ID69371 15 Jan 2020
How do I use the spectrum analyzer function on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the spectrum analyzer capability on the MDO3000 mixed domain oscilloscope. The MDO3000 contains a full-fledged spectrum analyzer with many useful features, including automatic markers, a
常见问题 ID69281 15 Jan 2020
I cannot see my signal on the Oscilloscope. What can I do?
You have many options to help diagnose this issue, below are a few suggestions to get started. If you find yourself needing more help, please connect with our Technical Support Center. You can get started by pressing the "Contact Us" button on the r
常见问题 ID63686 15 Jan 2020
: Can the optional AFG in the MDO3000, MDO4000C and 5 Series MSO be set to sweep?
AFG in MDO3000, MDO4000C, and 5 Series MSO do not have sweep function. But a limited sweep may be created using the arbitrary function.   Example: Create a sweep from 100 KHz to 250 KHz. ArbExpress (free software on Tek.com) select Equation Editor an
常见问题 ID474056 15 Jan 2020
How do I utilize the math channel feature on a DPO/MSO/MDO3000 or DPO/MSO/MDO4000 Series oscilloscope?
There are three main functionalities on the Math button on this scope. They range from Dual Waveform Math, FFT (Fast Fourier Transform), and Advance Math. These three functionalities have a range of abilities and are explained in this short YouTube v
常见问题 ID64656 15 Jan 2020
Is there a mictor adapter for the P6616 (logic probe for MSO5000B, MSO4000B, and MDO4000C + MDO4MSO) or P6516 (logic probe for the MSO4000 Series) or the P6316 (logic probe for MSO2000, MSO3000, MDO3000 + MDO3MSO Series)?
A mictor adapter is available from our partner Nexus Technologies. Use the mictor adapter NEX-HD2HEADER http://www.nexustechnology.com/products/laAccessories/hd2header/  
常见问题 ID59716 15 Jan 2020
Why do I see 16 flat lines for the MSO digital logic inputs when the same signals are displayed properly on the analog channels and all channels are setup for valid trigger threshold levels?
A common mistake for some, we first recommend verifing that the front panel MSO digital probe is properly connected by squeezing the probe's side latch buttons to un-plug, remove the probe then re-insert the probe label side up into the front panel r
常见问题 ID60251 15 Jan 2020
How do I mount a network drive on my MDO3000 or MDO4000C oscilloscope?
This procedure also applies to the DPO/MSO/MDO4000/4000B series oscilloscopes.  Note: This Mount a network drive will not work with a direct (peer-to-peer) connection. Must go through your local DNS server. To begin, press the “Menu” button in the S
常见问题 ID66201 15 Jan 2020
How do I connect an SMA male output to Oscilloscopes with TekVPI BNC inputs?
Use a Tektronix part number 015-0572-XX SMA female to BNC male adapter. This adapter will plug onto the BNC on the front of the scope and connect to a SMA cable. For more questions please press the "Contact Us" button on the right of the screen.   
常见问题 ID63516 15 Jan 2020
How do I set up a USB bus decode?
First you must have the USB module or option key that enables USB decoding for your scope as well as proper probes. For help finding the right probe use our probe selector tool. When you go into the bus option you must select USB and then make sure y
常见问题 ID64726 15 Jan 2020
My Tektronix oscilloscope uses the Linux operating system.  Where do I get a copy of the linux open source code as stated in the GNU Lesser General Public License notice?
For our Linux based instruments or programs licensed under the “GNU General Public License (GPL) or Lesser GNU General Public License (LGPL)” the complete corresponding sources are available. You can order a complete machine-readable copy of the sour
常见问题 ID64866 15 Jan 2020
How do I utilize the XY display feature on a DPO/MSO/MDO4000 Series oscilloscope?
The XY display format can be used to measure the phase relationship between two or more synchronous signals. This measurement technique involves inputting one signal into the vertical system as usual and then another signal into the horizontal system
常见问题 ID64666 15 Jan 2020
Can the MDO3000 capture the time domain and the frequency domain simultaneously?
The MDO3000 is most importantly an oscilloscope, but has a total of 6 different instruments individually built into it. Designed in such a way to minimize the clutter on your bench but give you the power and versatility you need. Unfortunately to be
常见问题 ID69306 15 Jan 2020
What are some of the benefits of the TekVPI probe interface?
The biggest benefits of the TekVPI™ probe interface are versatility and ease of use. Oscilloscopes with TekVPI interface support a wide range of probes including TekVPI probes, BNC and TekProbe-BNC Level 1 probes, and TekProbe-BNC Level 2 probes (v
常见问题 ID56016 15 Jan 2020
What are the maximum power draw ratings for the MDO3000 TEKVPI probes?
The MDO3000 has a max power draw of 25 Watts. The download link below provides a PDF listing of wattage draw for different active probes and max limits of Tektronix scopes, this will help determine the connection options available for any scope you h
常见问题 ID69301 15 Jan 2020
How do I Set Up a LIN serial Bus decode?
For doing Local Interconnect Network (LIN) bus decode Tektronix recommends using a DPO/MSO/MDO series oscilloscope. This feature can be purchased as a module or option key on any of these types of oscilloscopes. Start by turning it on the bus channel
常见问题 ID64781 15 Jan 2020
My company purchased a Tektronix MDO4104C oscilloscope last year and we purchased three application modules. They are not showing up on our scope anymore and we would like some help getting them back.
Push Utility on the front panel. If needed, push Utility Page on the lower menu and turn multipurpose knob a to select Config.  Push Manage Modules and Options on the lower menu, and then push License Type on the side menu until “Modules” is selected
常见问题 ID468031 15 Jan 2020
What probes are supported on the RF input of the MDO3000 and MDO4000 series?
The RF input on the MDO3000 and MDO4000 series has an N connector, so the RF input can support cables, antennas, and other adapters typically used with a spectrum analyzer.  The RF input is 50 ohms and it is AC coupled.  Below is a listing of some
常见问题 ID64506 15 Jan 2020
How do I use the MDO3000 to generate a frequency response curve?
The MDO3000 boasts a 50 MHz noise generator as a feature in the function generator, which can be used in conjunction with the wide-capture-bandwidth spectrum analyzer to produce a frequency response curve for an electronic system or device. The noise
常见问题 ID69351 15 Jan 2020
How do I run a Signal Path Compensation (SPC) on an DPO/MSO/MDO4000 Series oscilloscope?
Signal Path Compensation (SPC) should be run anytime you are getting DC offsets in your signals, or your scope has moved locations and might have changed temperature, or if it's been more then a month since your last SPC. This is a standard procedure
常见问题 ID64681 15 Jan 2020
Companies such as National Instruments and LeCroy sell USB-to-GPIB adapters. How do their adapters compare to the TEK-USB-488?
The products from National Instruments (GPIB-USB-B or GPIB-USB-HS) and LeCroy (WS-GPIB) are USB host to GPIB device adapter. These would be used for instruments that have a GPIB interface with controllers that have a USB port. The TEK-USB-488 was des
常见问题 ID56456 15 Jan 2020
Why does the Tkdpo2k3k4k_ReadWaveform() function in the Tkdpo2k3k4k IVI-C driver time out every time I call it when I am connected to the instrument via Ethernet? The function call works fine over USB, but over Ethernet it always times out.
The Tkdpo2k3k4k_ReadWaveform() function makes use of the Service Request Event in VISA so the scope can notify the driver when it has completed its acquisition and the waveform data is ready to be fetched as opposed to the driver polling the scope fo
常见问题 ID72221 15 Jan 2020
How do I use the Channel Monitor feature on the MDO3000 logic analyzer?
See attached PDF, which has explanations with images. 
常见问题 ID69391 15 Jan 2020
How do I reduce noise on signals using an oscilloscope?
There are many methods to reduce many types of noise on a signal. Tektronix oscilloscopes can do this through bandwidth limiting the scope input, averaging your signal, changing the sampling method to hi-resolution mode, and more. This video demonstr
常见问题 ID64706 15 Jan 2020
How do I save and load a reference waveform to a DPO/MSO3000 series oscilloscope?
This Video will explain how to setup, save and load a reference waveform. It can be done through a USB flash drive or by internal memory. This method for using reference waveforms can be applied to all MSO/DPO2000, MSO/DPO3000, MSO/DPO/MDO4000 serie
常见问题 ID64641 15 Jan 2020
How do I set up a CAN bus decode?
Depending on what scope you have will depend on what options are availiable for decoding your CAN signal. For all the DPO/MSO2000/3000/4000/5000 and MDO3000/4000 Series scopes there are modules or license keys that can be purchased. Once you have one
常见问题 ID64751 15 Jan 2020
Programing - How to get and plot a waveform from DPO/MSO/MDO4000 Series scope in Python
There are a few things that are needed for programming with an oscilloscope. First it's important to have a copy of your oscilloscopes Programmers manual. This can be found be searching for manuals on Tek.com and specifying Programmers manual in the
常见问题 ID64796 15 Jan 2020
How do I use the DVM and frequency counter function on the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the digital voltmeter and frequency counter functionality of the MDO3000 series mixed domain oscilloscope. The DVM can use any of the 4 analog scope inputs to feed the signal into a free
常见问题 ID69286 15 Jan 2020
What is aliasing and how do I detect it and fix it on my oscilloscope?
Aliasing is basically a form of under sampling and what is displayed on the scopes is an indistinguishable waveform. The under sampled waveform is then contstructed to look like a slower frequency waveform or a flat line in the case of the sample rat
常见问题 ID64691 15 Jan 2020
How do I clear my memory using TekSecure on a MSO/DPO/MDO4000 Series oscilloscope?
This procedure for clearing the memory on oscilloscope can be applied to the DPO/MSO/MDO4000, DPO/MSO3000 and DPO/MSO2000 Series oscilloscope families. By clearing the memory you will lose all saved reference waveforms, saved setups and all other set
常见问题 ID64686 15 Jan 2020
Will the DVM work on the MDO3000 series scope with a probe?
Yes,  the DVM works through the analog inputs, therefor you can use standard probes. If you have more questions please contact one of our Technical Support Centers and an Application Engineer will quickly answer your questions. 
常见问题 ID69331 15 Jan 2020
Can active probes with TekProbe interface (such as a P6205) be used on the DPO4000B or MSO4000B series scopes?
Yes. A TPA-BNC adaptor is required for people to connect legacy TekProbe interface probes to the new TekVPI interface. The adapter works on any TekVPI scopes inlcuding the MSO/DPO/MDO4000/B/C, MSO/DPO/MDO3000 MSO/DPO2000/B or MSO/DPO5000/B or DPO7000
常见问题 ID60416 15 Jan 2020
Can existing MSO3000/DPO3000  scopes be upgraded/modified to a MDO3000?
No, there is no conversion path to go from an existing MSO/DPO3000 to a new MDO3000. If you have more questions please contact one of our Technical Support Centers and an Application Engineer will quickly answer your questions. 
常见问题 ID69326 15 Jan 2020
How can I change the TekVISA Instrument descriptor “device name” used to identify the oscilloscopes to which I routinely connect?
Open TekVISA V4.0.0+ OpenChoice Instrument Manager by selecting Start -> All Programs -> TekVISA ->  OpenChoice Instrument Manager.Select (highlight) the Instrument descriptor listed in the Instruments list for the connected Oscilloscope.Cli
常见问题 ID66181 15 Jan 2020
What cart does my scope use?
Below are the Instrument Carts that can be purchased from Tektronix.                                         K4000                                                                             K420                              K475 More information can
常见问题 ID64561 15 Jan 2020
How do I use the serial decoder function on the MDO3000?
Hello and welcome to Tektronix, today I’m going to demonstrate the serial decoder capabilities of the MDO3000 series mixed domain oscilloscope.The MDO3000 has the ability to decode bus data into binary, hexadecimal, decimal, or ASCII values depending
常见问题 ID69296 15 Jan 2020
How Do I Set Up a Parallel Bus Decode?
For doing Parallel Bus decode Tektronix recommends using a MSO or MDO + MSO option Series oscilloscopes. This feature comes standard in the Bus menu and can be used in a variety of ways. Start by turning it on, selecting the channel and setting your
常见问题 ID64771 15 Jan 2020
How do I know if an AC signal applied to the MDO3000/4000/B RF 50 Ω input is going to exceed the maximum input power rating, and cause clipping, or damage?
MDO3000, MDO4000/B Advanced Math equation will calculate the AC signal's equivalent RF power in dBm, and the automatic High measurement will determine the maximum average power level of the AC signal applied to the 50 Ω analog input channel. Caution:
常见问题 ID69366 15 Jan 2020
If I upgrade my MDO3000 bandwidth do I receive higher bandwidth probes?
New, higher bandwidth probes are provided if the upgraded scope bandwidth exceeds the original supplied probes bandwidth.For example: If you upgrade a MDO3054 (500 MHz) to the MDO3104 (1GHz), you will also receive 4 TPP1000 (1 GHz probes) with the up
常见问题 ID69381 15 Jan 2020
Why Should My Signal Fit Within The Screen Of My Tektronix Oscilloscope?
Scaling your signal to fit within the screen will remove signal distortion caused by clipping. Clipping is caused by exceeding the limits of the instrument's input. Tektronix's digital oscilloscopes are designed such that each division is 25 digital
常见问题 ID60306 15 Jan 2020
How do I set up a RS232 bus decode?
The procedure to set up a RS232 bus decode and trigger is simple once you understand the basics. First you need to have the correct module or scope option. Second make sure your signal is on screen and taking up as much of the screen as possible with
常见问题 ID64761 15 Jan 2020
How do I use the mixed signal analysis function of the MDO3000?
Hello and welcome to Tektronix! Today I’m going to demonstrate the mixed signal capabilities of the MDO3000 series mixed domain oscilloscope.Much like its MSO predecessor, the MDO3000 boasts a 16-channel logic analyzer in addition to its 4 analog inp
常见问题 ID69291 15 Jan 2020
What is the maximum bit rate a decoded SPI bus can trigger on?
Different oscilloscopes have different triggering circuitry therefor the limits of what speeds can be achieved vary by scope. Please use the following table to easily look up your scope and determine your max SPI bus trigger level.  For more question
常见问题 ID62256 15 Jan 2020
MDO3000混合域示波器MDO4000混合域示波器,保存文件生成时间异常该如何处理
仪器时区与PC电脑设置不一致会导致在PC端查看文件生成时间异常。 开机后,进入系统设置菜单,除了需要设置时间,也需要设置时区,中国为UTC: -8.0
常见问题 ID473296 30 Dec 2019
MATLAB ICT plot points_通过Matlab绘制波形
使用Matlab从示波器中读取波形数据并绘制。 请注意相关软件配置环境以及VISA resource地址。Tektronix公司不负责该例程的完整性、可执行性和正确性。
Software 27 Dec 2019
CSharp NI-VISA Send Waveform to MDO AFG_使用CSharp发送数据MDO内置AFG
本例程提供了基本使用C#对MDO内置AFG进行控制,发送数据到MDO的AFG中,实现数据回放。 请注意相关软件配置环境以及VISA resource地址。Tektronix公司不负责该例程的完整性、可执行性和正确性。
Software 27 Dec 2019
调试嵌入式系统设计中的串行总线
今天,嵌入式系统几乎遍布在人类社会的每个角落。嵌入式系统可以简单定义为属于大型系统或机器一部分的一种专用计算机系统,其目的是为该系统或机器提供监测和控制服务。典型的嵌入式系统在开机时会开始运行某些专用应用,直到关闭时才会停止。当前设计和生产的几乎每个电子设备都是嵌入式系统。 了解使用泰克示波器强大的触发、解码和搜索功能怎样以极高的效率解决串行调试挑战。

文献编号: 48W-19040-21
应用指南 27 Dec 2019
测试一个新的开关模块的电源设计海报
Get a quick overview of the key measurements for verifying a new switch mode power supply (SMPS) design.  This poster shows key measurements, from verifying your prototype during initial startup, to optimizing switching loss and magnetic losses, to v

文献编号: 46W-60156-0
海报 27 Dec 2019
泰克EDI CON2015上展示价格亲民、性能卓越的最新无线射频测试测量解决方案
包括RSA306频谱分析仪、MDO4000B和MDO3000混合域示波器以及最新的TSG4100A矢量信号发生器等将集体亮相中国 北京 2015年4月14日----全球示波器市场的领导厂商---泰克公司日前宣布,在4月14日--16日中国北京国家会议中心举办的电子设计创新会议(EDI CON)上,泰克公司将重磅推出亲民价格、性能卓越的无线射频解决方案,包括RSA306频谱分析仪、MDO4000B和MDO3000混合域示波器以及最新的TSG4100A矢量信号发生器等将集体亮相。此外,泰克还将展示针
新闻稿 27 Dec 2019
示波器选型指南
从基本信号校验到高性能分析,这份12页的选型指南概括介绍了泰克全系列示波器。对照表给出了高级指标和特点,指明了每个系列的示波器之间的主要差异。下载PDF了解更多

文献编号: 46W-31080-7
选型指南 27 Dec 2019
Wave Inspector® :简化波形分析
随着摩尔定律推动着电子技术的速度不断加快,系统设计正变得越来越复杂,其设计、构建、调试及中断修复越来越困难。这一切对现代示波器又意味着什么呢?现代数字示波器可以捕获海量数据。直到现在,搜索这些数据一直是一个耗时麻烦的过程。通过泰克WaveInspector® 导航和搜索功能,您可以以不同于任何其它示波器的效率和精度,获得所需的答案。

文献编号: 48T-19039-9
应用指南 27 Dec 2019
Tektronix 示波器附件选择指南
示波器探头相互参考, 无源探头, 有源探头, 差分探头和差分前置放大器, 电流探头, 高压探头和高压差分探头, 连接器和适配器, 光电转换器, 衰减器, 端接器和电缆, 仪器手推车/机架安装套件, 探头尖附件

文献编号: 60W_14232_10
产品选择器指南 27 Dec 2019
低电容探头最大限度地降低对电路操作的影响
本应用指南介绍了泰克高带宽,低电容无源电压探头怎样降低示波器用户的总拥有成本、改善性能和测量精度及节约用户设置时间。大多数示波器标配的无源电压探头都提供了低成本通用探测解决方案。一般来说,这些探头没有有源电压探头的性能,但坚固耐用、动态范围宽,适合查看信号。

文献编号: 51W-26294-6
应用指南 27 Dec 2019
在选择示波器时要考虑的10件事
选择哪种示波器,不仅要符合您的工作方式和工作地点,还要有准确捕获信号的精度,以便提升测试性能,满足您工作测试需要。本指南清晰罗列了所要考虑的重要因素,并结合实际案例进一步剖析每个点的重要性,帮助您最大限度地提高生产效率。 

文献编号: 3GW_60848_1
手册 27 Dec 2019
使用任意波形 函数发生器复现真实世界信号
这篇应用文章将给您关于泰克AFG3000系列以及ArbExpress应用软件的详细的步骤演示

文献编号: 76W-18661-2
应用指南 27 Dec 2019
如何快速准确的定位性能验证中模拟信号的异常
在做产品的性能验证当中异常的诊断是工程师面临最大的挑战,因为异常具备偶发性和不确定性,如何能够快速准确的定位异常问题成为性能验证的关键。下载应用文章,您将了解到如何迅速验证和调试数字信号和模拟信号的细节。
应用指南 27 Dec 2019
汽车电子解决方案手册
The pace of change in automotive electronics has never been faster, resulting in safer, more efficient, and more connected vehicles. Technologies such as high-speed data communications, wireless communications, radar, and power supplies underpin thes

文献编号: 45W-60646_1
手册 27 Dec 2019
深入了解示波器
在阅读《深入了解示波器》介绍的概念后,您将能够初步了解示波器的基础知识和工作原理: 描述示波器的工作方式 描述各种示波器之间的差异 描述电气波形类型 了解基本示波器控制功能 进行简单的测量

文献编号: 03Z-8605-7
入门手册 27 Dec 2019
如何利用示波器探头进行电源转换器的高精度电压测量
应用指南 27 Dec 2019
使用示波器测量开关损耗
随着人们需要改善功率效率,延长电池供电的设备的工作时间,分析功率损耗及优化电源效率的能力比以前变得更加关键。效率中一个关键因素是开关器件的损耗。本应用指南将概括介绍这些测量,以及使用示波器和探头进行更好、更可重复的测量的部分技巧。
应用指南 27 Dec 2019
MDO3000 Series vs. Agilent MSO/DSO3000 X-Series
Examine the MDO3000 Series vs. the Agilent MSO/DSO3000 X-Series.

文献编号: 48W-30078-0
竞争 27 Dec 2019
MDO3000系列混合域示波器的101种用途
通过融合示波器和频谱分析仪的功能,混合域示波器可以使用一台仪器,同时在时域和频域中工作。毫无疑问,一旦到位,您可以通过各种方式使用MDO3000,而下面则列出了您可以考虑完成的101 项任务。

文献编号: 48C-30122-0
应用指南 27 Dec 2019
MDO 信号通路拆卸海报
MDO4000 and MDO3000 Mixed Domain Oscilloscopes deliver uncompromised oscilloscope performance combined with spectrum analyzer performance on par with standalone spectrum analyzers. But how do they do it? The answer lies in Tektronix’ custom ASICs, a

文献编号: 48W-60186-2
海报 27 Dec 2019
从今以后:定制您自己的示波器—MDO3000系列混合域示波器

文献编号: 48C-30066-0
应用指南 27 Dec 2019
使用台式示波器进行电源测量和分析
当今电源正走向前所未有的效率水平,要求设计工程师执行专门的电源测量,这些测量不仅耗时长,而且非常复杂。了解怎样使用泰克台式示波器,提供快速简单的分析及自动电源测量。

文献编号: 3GZ-23612-6
应用指南 27 Dec 2019
使用混合信号示波器调试数字电路的技巧应用指南
电子产品的速度越来越快,这意味着设计、验证和调试也更难。在发生问题时,设计人员必需迅速了解根本原因,以便解决问题。通过同时分析信号的模拟表示方式和数字表示方式,许多数字问题的根本原因都可以迎刃而解,您将学习怎样使用MSO 和MDO 系列示波器的基本逻辑分析仪功能迅速验证和调试数字电路。

文献编号: 3GC-24008-4
应用指南 27 Dec 2019
使用任意波形 函数发生器复现真实世界信号
这篇应用文章将给您关于泰克AFG3000系列以及ArbExpress应用软件的详细的步骤演示

文献编号: 76C-18661-0
应用指南 27 Dec 2019
MDO3000系列混合示波器使您的工作更简单更迅速
Save hours verifying and debugging your designs using a scope developed to make your job simpler and faster. Work from DC to RF, with analog and digital signals, and serial and parallel buses.

文献编号: 48W-30067-0
应用程序概述 27 Dec 2019
使用泰克示波器和选配软件支持串行总线
泰克示波器提供了一系列选配的分析功能,简化了串行总线调试或一致性检验。本选型指南说明了示波器系列中每款产品支持哪些串行标准。

文献编号: 55W-29028-13
选型指南 27 Dec 2019
Measurements Matter Flyer

文献编号: 48W-60968-1
特点 27 Dec 2019
MDO3000 系列 用户手册
Oscilloscopes User Manual

部件号: 077097500
Manual 26 Dec 2019
MDO3000 Series
Oscilloscopes User Manual

部件号: 077096801
Manual 26 Dec 2019
MDO3000 系列 用户手册
混合域示波器

部件号: 077097502
Manual 26 Dec 2019
Read This First
Update Your MDO3000 with the Latest Firmware

部件号: 061440200
Manual 26 Nov 2019
MDO3000 Series
Oscilloscopes

部件号: 077097900
Manual 26 Nov 2019
MDO3000 Series
Oscilloscopes User Manual

部件号: 071324902
Manual 26 Nov 2019
MDO3000 Series
Oscilloscopes User Manual

部件号: 071324900
Manual 26 Nov 2019
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

部件号: 077051009
Manual 26 Nov 2019
MDO3000 Series
Oscilloscopes Application Module Installation Manual

部件号: 071325000
Manual 26 Nov 2019
MDO4000C, MDO4000B, MDO4000, MSO4000B, DPO4000B, and MDO3000 Series
Digital Oscilloscopes

部件号: 077051007
Manual 26 Nov 2019
MDO3000
Mixed-Domain Oscilloscopes

部件号: 077098100
Manual 26 Nov 2019
MDO3000 Series Oscilloscope
Declassification and Security Instructions

部件号: 077098000
Manual 26 Nov 2019
MDO3000 Series
Oscilloscopes User Manual

部件号: 071324901
Manual 26 Nov 2019